Project:Amanda Enterprise 4.1 > NDMP Backup & Restore

NDMP Backup & Restore

Table of contents
No headers

Amanda Enterprise supports backup and recovery of NDMP appliances using NDMPv4 (version 4) protocol. It does not support earlier versions of NDMP protocol. Amanda Enterprise supports Remote NDMP, Direct NDMP as well as 3-way NDMP configurations. 

In Remote NDMP configurations, NDMP appliances such as Netapp Filers, Sun Unified Storage, EMC Celera and BlueArc storage are backed up to tape changers and disk attached to the Amanda server. Any NDMPv4 compliant device is likely to work with Amanda Enterprise. The backup and recovery data goes through the server. In Direct NDMP and 3-way NDMP configurations, Appliances can be backed up to a tape changer that is attached to a SAN or using iSCSI and is accessible from the appliance. The backup and recovery data is not transferred through the server. The Amanda backup server acts as a backup control program.  

NDMP backup and recovery in Amanda Enterprise is implemented as an Amanda application. As a result, management of NDMP backup and recovery is identical to other applications. The Amanda disk list entries (DLEs) for NDMP can be present in a backup set that has other application DLEs. This configuration is not recommended. 

The NDMP backups from an appliance can be restored to an appliance from the same vendor.  


Requirements for NDMP Backup and Restore  

Amanda server must be running linux or Solaris distribution listed on the Zmanda Network Supported Platforms page. 

  • Amanda Enterprise server (including dependencies) must be installed on the Amanda server. 

  • The Amanda server includes the NDMP application. The NDMP backup can be performed only from the Amanda server not from Amanda client. 

  • If there is a firewall on the Amanda server, a firewall rule should be added to trust each NDMP device being backed up. 

  • NDMP services must be enabled on the appliance. For example: the following figure shows how to check if NDMP services are enabled on BlueArc Storage. 




No additional packages are required for NDMP application. Amanda server includes all the necessary software. 

  • Zmanda's NDMP application module is a licensed application. All product licenses from Zmanda are in a single license file. If you have bought licenses recently, you will have to download the license file from Zmanda Network. The license file should be uploaded on the on the Amanda server.  


  • Configuring NDMP Volumes/Directories for Backup  


Configuring NDMP backups requires configurations steps using Zmanda Management Console and some manual steps. 

  • Zmanda recommends creation of separate backup set for NDMP backup. 

  • Create a backup set for the NDMP appliance in the Zmanda Management Console. 

  • Add the new NDMP entries to the backup set using the Sources page. Begin by selecting NDMP from the File System drop down menu. The following figure shows an example backup configuration of /vol/zmanda_fs1 from Netapp Filer with IP address This filer is configured for Amanda data path i.e, the Netapp volume is being backed up to a storage device (disk, tape changer or cloud) attached to Amanda server. 






Filer Host Name is the IP address or host name of the NDMP appliance. 

VolumeName is the name of NDMP volume. 

Directory is the directory in the NDMP volume that is being backed up. 

Vendor is the NDMP appliance type. It can be Netapp, BlueArc, EMC Celera or Sun Unified Storage. 

The Username and Password are the user credentials for performing backup and recovery from the NDMP appliance. The user should have privileges to perform NDMP backup and recovery.  

Auth type can be MD5 or Text. This is the type of authentication used to connect to the NDMP appliance from the Amanda server. 

Data Path can be DirectTCP or Amanda. The DirectTCP provides LAN free backups i.e, backups are sent directly from the appliance to the tape changer. The Amanda data path allows the user backup to NDMP appliances to the media accessible from the Amanda server. For DirectTCP data path, the staging area is automatically disabled. 

You can use only Amanda or DirectTCP data path in an Amanda server.  

Compression, Data Deduplication and Encryption cannot be used for DirectTCP data path. CompressionData Deduplication and Encryption can be performed for Amanda data path. 

Click Save to save the configuration to the backup set. ZMC performs automatic verification of the configuration, when the configuration is saved. 


Scheduling Backups of NDMP Appliance  


You can schedule backups using Zmanda Management Console Backup When page or run immediate backups for the backup set from the Backup Now page. 

The status of the backup are shown in the Monitor Page. Backup reports will be available under theReporttab in the Zmanda Management Console. 


Performing NDMP Restores using ZMC Edit section 

Use Zmanda Management Console Restore What page to select the backup images to be restored. The following figure shows restoration of NDMP appliance/filer with IP address and directory/<PATH>. You can select backup you want to restore from using the Backup Date field. The Host Name field is always for NDMP application. 


Only Express Restore is supported for NDMP at this time. 

In the Restore Where page, you can select where you want the data to be restored to. You can select a different appliance/filer or different directory as restoration target as shown below. 


Data from a NDMP vendor can be restored only to the same vendor appliance.  

Go to Restore Now page to start the restoration process. Amanda Enterprise does not support Direct Access Recovery (DAR). 


Performing NDMP Restores using Command Line  

This section describes how to use Amanda recovery command amrecover to perform NDMP volume/directory restoration.  

  1. Run amrecover command on the Amanda server as root user. You will need to provide the backup set name as a parameter. The values for options -t and -s will not change. 
        # amrecover -C <backup set name> 

  1. Set the host to and the disk to DLE name that was used in the backup set configuration (use amrecover listdiskcommand to figure out the correct host and DLE name). The DLE name will have //<ip address or the name of filer>/<volume name>/[<directory name>]. NDMP authentication file must be configured in the /etc/amanda/<backup set name>/ndmp_filer_shares configuration file for the filer 

amrecoversethost localhost 

200 Dump host set to localhost. 

amrecoversetdisk // 

200 Disk set to // 

  1. You can list the files in the backup using ls command. Add all the files or specific files to be restored and run extract command to restore the files. 


amrecover> ls 

2010-03-03-17-22-35 MyData 
2010-03-03-17-22-35 MyMusic 

amrecover> add * 
Added file /MyData 
Added file /MyMusic 

amrecover> extract 


  1. The amrecover command asks you to load the necessary tapes to the tape changer. Confirm that the tapes are loaded. The files will be restored to the original location. Please note that existing files in the original location will be deleted. 

  1. To restore to an alternate location on the filer or another filer (filer authentication information must be in/etc/amanda/<backup set name>/ndmp_filer_shares configuration file), you can use set property directory. 

amrecoversetproperty directory // 


Improving Backup Performance  


This section provides guidelines on how to improve backup performance for NDMP backups from Netapp appliances.

These guidelines are applicable for Oracle/ Sun as well BlueArc appliances also (please refer to appliance manual for configuration). 

  1. Netapp filers supports upto 16 backup and restore operations at a time. We can split volumes to be backed up into multiple backup sets and do them in parallel. This will work well for 3-way NDMP configurations because Amanda server is not a bottleneck. 

  1. Activity on the Netapp filer during backup run will impact backups. NDMP jobs have the lowest priority compared to all other tasks on the Netapp filer. 

  1. Check whether DAR is disabled on the filer. This change will have significant improvement in backup performance. 


  3. Run the following command on the Netapp filer: 

options ndmpd.offset_map.enable off 

Check for faulty disks in the aggregate used for the volume being backed up. This can impact the backup performance.